The TrolMaster DSP-2 program device module (timer module) works like a multi-function timer. The DSP-2 allows the user to easily connect any device that needs to be controlled by TIME to the Hydro-X. Any device that is 10-amps at 240 volts or less can be controlled by the DSP-2.

The TS-2 thermostat station is designed to replace a thermostat connected to a standard HVAC unit. The TS-2 can be used to control most HVAC systems including heat pump and multi-stage HVAC systems. The  TS-2 is wired to the HVAC system using the same low-voltage thermostat cable, and has the standard color-coded wiring as most thermostats. The Hydro-X allows separate Day and Night settings for each of up to (4) TS  modules, so multiple HVAC systems can be controlled by a single Hydro-X system. The TS-2 also has an adjustable delay time for each HVAC systems being activated. That minimizes high start-up (inrush current) and allows up to 4 HVAC systems to be safely controlled

The TS-1 thermostat station is designed to replace a thermostat connected to a conventional cool only HVAC unit. The TS-1 is wired to the HVAC system using the same low-voltage thermostat cable, and has the standard color-coded wiring as most thermostats. The Hydro-X allows separate Day and Night settings for each of up to (4) TS  modules so multiple HVAC systems can be controlled by a single Hydro-X system.

The optional Water Detector WD-2  allows the user to detect water leaks or water on the floor of the facility. Simply place the water sensor at floor level (or wherever you want to watch out for water leaks). Up to 5 Water detectors can be connected to a single Hydro-x controller. If ANY of the sensor detects a water leak, the unit will send a user-alert to notify user of a water leak.

The WD-1 water detector can be used in one of two ways. First, it can be used to simply monitor the floor or a space for water… as a leak-detector. The other way the WC-1 can be used is as a water-verification monitor. When used in this way, the water detector is placed where runoff will accumulate (or where water is being introduced to the growing medium). Each output (solenoid or pump) on the Aqua-X can be “assigned” to a specific WD-1. Every time the solenoid or pump assigned to the WD-1 is activated by the Aqua-X, the WD-1 must detect water within a adjustable delay time. If water is not detected (pump or solenoid failure) the Aqua-X will send out a user alert notifying of the “irrigation failure.” Up to 25 WD-1 can be connected to a single Aqua-X.

The TrolMaster pH probes provide accurate and reliable monitoring on the pH of the water being monitored by the Aqua-X. The PPH-2 probe is a commercially rated probe and it connects to the Aqua-X via the AMP-2 Sensor Board. It is intended to be used inline with existing pvc piping and also can be placed into an water tank.

The OA6-24 control board is designed to control multiple 24vac solenoid valves.

It provides an easy and efficient method to control up to 6 valves… each with individual timer settings. Up to 5 OA6-24 can be connected to a single Aqua-x providing a maximum of 30 individually controlled outputs to connect to your solenoid valves. The Aqua-X can also provide a “master pump link” by using a DSP-1 along with the OA6-24. Connecting a DSP-1 to the OA6-24 provides an automatic “pump link” between the DSP-1 and the OA6-24. When any of the 24vac irrigation zones are activated on the OA6-24, the DSP-1 will automatically turn on the pump.

The Aqua-X system is a professional-grade irrigation control system. It is a fully customizable modular designed system. Installation is simple and the system is easy to expand upon. The Aqua-X is designed to control up to 30 separate irrigation zones (24vac solenoid valves or 120vac pumps),  The Aqua-x monitors pH / EC and water temp as well as to monitor actual growing medium moisture levels by using up to (8) Water Content Sensors connected to a single Aqua-x controller. The timers can be set-up to be recycling timers, or to operate at specific time of day and durations. With the free TrolMaster App, the user can access all of the settings and alerts on the system from anywhere at anytime.

The NFS-1 is the brain of the Aqua-X system. It comes with a water detector WD-1 for leaking alert and watering confirmation.

The Full Spectrum Quantum Sensor (MBS-PAR) provides accurate and cost-effective measurement of photosynthetically active radiation (PAR) from all light sources used to grow plants. The full-spectrum quantum sensor has a spectral range of 389 to 692 nm ± 5 nm. The improved spectral response increases the accuracy of LED measurements.

Used in conjunction with the Hydro-X controller, the PPFD sensor will AUTOMATICALLY increase or decrease the output level of your supplemental lighting systems to continuously maintain the exact lighting level (in PPFD) that the user selects.

"Sensors should remain dry and clean to prevent premature failure. Do not spray foreign substances or allow water / condensate on the sensors"

The optional Smoke Detector (MBS-SD) can alert the user to smoke within their growing area at ALL TIMES. Up to 5 smoke detectors can be connected to a single Hydro-x controller. If ANY of the smoke detectors determine there is smoke in the area, the user will receive a user-alert on their phone to alert them to the potential problem BEFORE the problem gets out of hand.

"Sensors should remain dry and clean to prevent premature failure. Do not spray foreign substances or allow water / condensate on the sensors"

TrolMaster’s Hydro-X system can control most of the supplemental lighting fixtures sold today. Most light manufacturers provide the ability to control their lighting systems using what known as a low-volt control. That low-volt control can take many forms and communication protocols. TrolMaster makes several types of lighting adapters (LMA units) that allow the Hydro-X to control lights using their low-volt control option.

The LMA-T works specifically with the ThinkGrow LED systems to provide two channel control, which allows separate control for full spectrum and second red output levels on the ThinkGrow LEDs.

The LMA-T simply connects to the lighting control ports Line 1 and Line 2 on the HCS-1. Once connected, the user can then set individual ON and OFF times and the dimming settings for the full spectrum LEDs and also for the second red LEDs.

The LMA-T then is connected to the RJ type lighting control cables where each of the LEDs are connected back to the controller in a daisy-chain configuration using plug-and-play connections.

One adaptor could run up to 256 ThinkGrow LEDs.

*Convert RJ12 to Water Proof Connector Cable included.

TrolMaster’s Hydro-X system can control most of the horticultural lighting fixtures sold on the market today. Most light manufacturers provide the ability to control their lighting systems using what known as a low-volt control. That low-volt control can take many forms and communication protocols. TrolMaster makes several types of lighting adapters (LMA units) that allow the Hydro-x to control lights using their low-volt control option.

Lantern lighting schedule is a lighting routine for vegging plant that you could find in any college grade horticulture book. It is as follows: 12 hours lights on, 5.5 lights off, 1-hour lights on, 5.5 lights off, and repeat schedule. The 1 hour on in between off periods fool the plants that stay in vegetative growth state.

This LMA-24 lighting adapter is specially designed to use both two channels on the Hydro-X system to create a lantern schedule control for any lights with 0-10V protocol. It is compatible with HIDs like Gavita/Nanolux/Luxx/Growers Choice/Illuminar/PL and LEDs like Fluence/Next light/Spectrum King.